M A T E R I A L S A F E T Y D A T A S H E E T Rev 13000.03B
For Coating, Resins, and Related Materials NPCA 1-84
MANUFACTURER'S NAME EMERGENCY TELEPHONE NO.
BENJAMIN MOORE & Co. 800-424-9300 (CHEMTREC)
51 CHESTNUT RIDGE RD.
MONTVALE, NJ 07645
DATE OF PREPARATION INFORMATION TELEPHONE
15-DEC-97 (Sup. 25-JUN-90) 201-573-9600
================================================================================
SECTION I - PRODUCT ID
================================================================================
HMIS CODE SARA TITLE 312
PRODUCT CODE: 130 | | | Acute: YES |
CLASS: SOLVENT THINNED PAINT | Health: 2* | | Chronic: YES |
NAME: MOORES HOUSE & TRIM PAINT | Flammability: 2 | | Fire: YES |
COLOR: ALL | Reactivity: 0 | | Pressure: NO |
| Personal Prot.: | | React: NO |
For a complete description of HMIS and explanation of the PERSONAL PROT:
code, see Section XX.
================================================================================
SECTION II - HAZARDOUS INGREDIENTS
================================================================================
INGREDIENT MAX PCT CAS NO.
TLV PEL STEL CEIL MM Hg TEMP
Stoddard Solvent (fn) 24.0 8052413
100ppm 100ppm 2.0 @ 20 C
Zinc Oxide (f*3n) 10.5 1314132
10mg/m3 10mg/m3 N/A
Calcium Carbonate (f*) 3.0 471341
10mg/m3 5mg/m3 N/A
Silica, Crystalline 0.2 14808607
(f*) .1mg/m3 .1mg/m3 N/A
Titanium Dioxide (f*n) 24.1 13463677
10mg/m3 10mg/m3 N/A
Magnesium Aluminum 3.1 12174117
Silicate (f*) 10mg/m3 N/E N/A
f Federal Hazard List
* Hazardous only as dust when product is sanded.
3 Sect. 313 of the Emergency Planning & Community Right-To-Know Act of 1986
and of 40 CFR 37
n New Jersey Label Law hazardous chemical
This product may contain small amounts of materials known to the
State of California to cause cancer and reproductive harm.
================================================================================
SECTION III - PHYSICAL DATA
================================================================================
BOILING RANGE: 310- 405 F VAPOR DENSITY: HEAVIER THAN AIR
WEIGHT PER GAL: 11.1 - 11.1
EVAPORATION RATE: SLOWER THAN ETHER % VOLATILE VOLUME: 42.2 - 42.2
================================================================================
SECTION IV - FIRE AND EXPLOSION HAZARD DATA
================================================================================
D.O.T. FLAMMABILITY CLASSIFICATION: COMBUSTIBLE FLASH PT.: 125 F PMCC
LEL: 1.0%
EXTINGUISHING MEDIA: FOAM CO2 DRY CHEMICAL WATER FOG
UNUSUAL FIRE AND EXPLOSION HAZARDS:
Closed containers may burst if exposed to extreme heat or fire.
Toxic gases may form when product burns.
SPECIAL FIREFIGHTING PROCEDURES:
Do not use water stream on burning liquid.
Cool exposed containers with water. Use self-contained breathing apparatus.
================================================================================
SECTION V - HEALTH HAZARD DATA
================================================================================
EFFECTS OF OVEREXPOSURE - ACUTE:
Inhalation - Harmful if inhaled. May affect the brain or nervous system,
causing dizziness, headache or nausea.
Contact - Causes eye irritation.
Contact - Causes skin irritation.
Skin Absorption - Hazardous ingredients contained in this product have the
capacity to be absorbed throught the skin in sufficient quantities to cause
systemic toxicity. See Safe Handling and Use Information (Section XII).
Ingestion - Irritation of the digestive tract and nervous system depression
(drowsiness, dizziness, loss of coordination and fatigue). Aspiration Hazard -
This material can enter lungs during swallowing or vomiting and cause lung
inflammation and damage. Hazard - This material can enter lungs during
swallowing or vomitting and cause lung inflamation and damage.
EFFECTS OF OVEREXPOSURE - CHRONIC:
Skin Contact - Prolonged or repeated exposure may cause dermititis.
Inhalation statement: Sanding dust inhalation may cause lung damage.
Contains: Crystalline Silica which has been determined to be carcinogenic to
humans (1) by IARC when in respirable form. Risk of cancer depends on duration
and level of inhalation exposure to dust from sanding dried paint or spray mist.
NOTICE: Reports have associated permanent brain and nervous system damage with
repeated, prolonged overexposure to solvents among persons engaged in the
painting trade. Intentional misuse by deliberately concentrating and inhaling
the contents may be harmful or fatal.
MEDICAL CONDITIONS PRONE TO AGGRAVATION BY EXPOSURE:
None expected when used in accordance with Safe Handling and Use Information
(Section VIII).
PRIMARY ROUTE(S) OF ENTRY: DERMAL INHALATION INGESTION
EMERGENCY AND FIRST AID PROCEDURES:
Inhalation - Remove from hazard area, maintain breathing, call physician.
Skin Contact - Remove with soap and water.
Eye Contact - Flush immediately with large amounts of water. Call physician.
Ingestion - Drink 1 or 2 glasses of water to dilute. Do NOT induce vomiting.
Call physician.
================================================================================
SECTION VI - REACTIVITY DATA
================================================================================
STABILITY: STABLE HAZARDOUS POLYMERIZATION WILL NOT OCCUR
HAZARDOUS DECOMPOSITION PRODUCTS: Burning may produce carbon dioxide and carbon
monoxide.
CONDITIONS TO AVOID: Elevated temperatures and build up of vapors.
INCOMPATIBILITY (MATERIALS TO AVOID): None reasonably foreseeable.
================================================================================
SECTION VII - SPILL OR LEAK PROCEDURES
================================================================================
STEPS TO BE TAKEN IN CASE MATERIAL IS RELEASED OR SPILLED:
Remove all sources of ignition. Avoid breathing vapors. Use non-sparking tools
to return materials to container. Absorb residue with Fuller's earth.
WASTE DISPOSAL METHOD:
Conventional procedures in compliance with local, state and federal regulations.
Do not incinerate sealed containers.
================================================================================
SECTION VIII - SAFE HANDLING AND USE INFORMATION
================================================================================
RESPIRATORY PROTECTION:
Wear a properly fitten vapor/particulate apporoved by NIOSH/MSHA for use with
paints (TC-23C) during application or sanding and until all vaports and spray
mist are exhaussted. In confined spaces or in situations where continuous
spray operations are typical, or if proper respirator fit is not possbile, wear
a positive pressure, supplied air respirator (NIOSH/MSHA TC-19C).
VENTILATION:
Adequate to maintain working atmosphere below T.L.V. and L.E.L. (See Sect. II
for ingredient data and concentrations). Mechanical exhaust may be required in
confined areas. Discharge exhaust only in area away from ignition sources.
PROTECTIVE GLOVES: Solvent impermeable gloves are required during repeated
contact.
EYE PROTECTION: Splash goggles or safety glasses with side shields.
OTHER PROTECTIVE EQUIPMENT: Clothing adequate to protect skin.
HYGIENIC PRACTICES:
Remove and wash clothing before reuse. Wash hands before eating,
smoking or using the washroom.
================================================================================
SECTION IX - SPECIAL PRECAUTIONS
================================================================================
PRECAUTIONS TO BE TAKEN IN HANDLING AND STORAGE:
Combustible - Keep away from heat and flame.
OTHER PRECAUTIONS:
Use only with adequate ventilation. Avoid prolonged contact with
skin and breathing of vapor spray mist or sanding dust.
Close container after each use. Keep out of reach of children. Do not take
internally.
================================================================================
SECTION XX
================================================================================
HMIS (Hazardous Materials Identification System) (R) NPCA
HMIS is a recognized workplace Hazard Communications System as required by OSHA
(40 CFR 1910.1200). Information on establishing a complaint hazardous
communication program using HMIS is available from:
American Lablemark Co., Inc., Labelmaster Division
5724 N. Pulaski Rd., Chicago, IL 60646
1-800-621-5808
The ratings assigned by Benjamin Moore & Co. are only suggested ratings; the
contractor/ employee has ultimate responsibility for HMIS rating where this
system is used.
PERSONAL PROTECTION: This code is left blank on Benjamin Moore & Co. MSDS's as
it depends on application technique and the workplace ventilation. Please read
Sections II through IX of this MSDS before deciding on appropriate protective
equipment and beginning work. There are codes available for this section which
can be obtained from Labelmaster.
Note: There are no SARA reportable materials in this product.